This is well worth the entire watch. It feels like what would any hacker do in trying to figure out how to make something they want to exist. Also very well presented and good pace.
Underactuated robotics are so cool. In the hobby BattleBots community, there is a design where the whole robot only has a single motor, but it's able to move in any direction and damage the opponent, all just by controlling the single motor's speed.
Most robots have at least three motors, two drive sides and a weapon motor. The trick to getting away with one is integrating an impactor into the chassis of your bot, using the single wheel to spin up to ~3k RPM, then by tracking the rotation angle of the bot as it spins, you speed up a little while the wheel is pointing where you want to go, and slow it down a little when it's pointing the other direction.
Well not just battlebots, real life 6th gen fighters now all lack the vertical stabilizer so they have to rely on very sensitive real-time software control of the elevator/spoilerons to do banks and yaws. Not sure if it counts as under-actuated but they are tremendously difficult to steer without computer control.
I'm not super familiar with heavy equipment like dozers and such, but some of them may also have a single motor to pressurize hydraulic fluid and valves to articulate the various pistons. So may be able to make the argument there too
That is common and you can't run two different cylinders at the same time. Depends on how the pump and valves are plumbed of course. Sometimes you can run more than one but you split power.
A really neat concept. It uses a special hinge design, a magnetic encoder and torque modulation to control the lift of the rotor as it spins. Completely negates the need for a conventional helicopter's swash plate.
The single motor does have the pretty major downside that it spins the moment it's in the air. I suspect a 2 motor drone with a tail motor would be a lot more practical. But I really like how mechanically simple the rotor hinge design is - it pushes all the complexity into the control algorithm.
Perhaps there are specific applications where the payload spinning could be an advantage, imaging/scanning perhaps (which in the video is going to be in the next iteration for the builder).
It's a pretty cool concept, however, fails to mention coaxial rotor design that has a single motor and has much simpler control systems. I am also curious on how this affects frame vibration.
This is a newer trend in mechanical design that leverages more complex control software to overcome mechanical issues. A good example is https://turntide.com/
Side note, I used those same moteus controllers for a decidedly less energetic use case (two axis gimbal for RF satellite tracking) and found them to be super high quality and the lead developer always super helpful. Been a few years but def worth a look if you want to get into motor control.
There's also been a few people building monocopters with a fixed, non tilting motor and prop, and four servo motor actuated fins at the bottom that can be used for thrust vectoring and to counter rotational forces.
It's incredible that changes in velocity still work to adjust the angle of the blades even at the insane speeds they're moving at. I would never have thought that was possible.
I have to wonder why this guy didn't give his drone a leash while testing so it couldn't go flying off. It's the first thing that popped into my head, so I'm sure it's something he thought of as well and didn't use for a good reason. Maybe a string would get caught in the blades?
Inspires me to try and start doing some robotics.
Most robots have at least three motors, two drive sides and a weapon motor. The trick to getting away with one is integrating an impactor into the chassis of your bot, using the single wheel to spin up to ~3k RPM, then by tracking the rotation angle of the bot as it spins, you speed up a little while the wheel is pointing where you want to go, and slow it down a little when it's pointing the other direction.
they are not humanly pilotable without computers. they are inherently unstable.
The single motor does have the pretty major downside that it spins the moment it's in the air. I suspect a 2 motor drone with a tail motor would be a lot more practical. But I really like how mechanically simple the rotor hinge design is - it pushes all the complexity into the control algorithm.
https://hackaday.com/2020/06/25/building-and-flying-a-helico...
https://www.youtube.com/watch?v=d80oXSCcHTk
This is a newer trend in mechanical design that leverages more complex control software to overcome mechanical issues. A good example is https://turntide.com/
Smaller, cheaper, more numerous offensive drones?
https://www.youtube.com/watch?v=u2cETOyuJ20
I have to wonder why this guy didn't give his drone a leash while testing so it couldn't go flying off. It's the first thing that popped into my head, so I'm sure it's something he thought of as well and didn't use for a good reason. Maybe a string would get caught in the blades?