You should design your home server with two layers of security. The actual server and apps should be secured in the same way you would a public application, and then wireguard on top. That way an exploit needs to compromise both layers at the same time. And with auto updates enabled the chance of that happening is low.
Compared to faffing around with certificates, Wireguard or if you're lazy, Tailscale, is a breeze to setup.
Generate the config, one per client, setup the client to only route specific RFC1918 networks and disable on well known wifi networks, and that's it. It literally works for years without any maintenance.
Tailscale is easier (presumably), but also puts a corporate entity between you and your data.
Tailscale is ridiculously easy, and headscale is a thing. It doesn't support everything corporate Tailscale does, but it covers the basics of "get me into my network from anywhere". You can run it on a $1/month VPS that has a public IPv4 address.
I don't work with computers professionally, at all. It still only took me about 2 hours to get the VPS, get Debian going on it, set up headscale, and connect to it from home. Do I still use corporate Tailscale? Yes, it has some features that aren't beautifully supported on headscale, and so for the moment I'm fine with that. But I do have my backup plan in place if I need it.
VPNs these days are far easier to configure than mTLS (which often need proxies on both server and client side to handle the TLS terminations and needing to worry more with certificate lifecycle).
mTLS is a better option for distributed systems (service to service mesh networks for attestation of workload identities) instead of for human users.
I want to make sure every picture I take will be backed up to the NAS.
Do I turn on the VPN when I take a picture and turn it off when finished? Every time?
What if I need multiple VPN's? Living in a country that has a bad geoip reputation, it's already a struggle of switching on and off for individual websites to work.
Strongly agree, Tailscale / WG is the way go. Unless something needs to be available to randos on the Internet, in which case mTLS is still a huge headache.
mTLS is the one that requires a client certificate. right? It can be quite difficult to get protocols other than HTTPS to behave well with that, mostly because the application has to worry about it and many don't bother.
WireGuard is also very much like SSH private keys.
A basic config to set up a VPN that only adds access to services on the VPN itself is very short and simple, both for WireGuard server and for WireGuard clients.
You can run the WireGuard server from your home computer. For example on your NAS machine itself or some other machine you have at home. And open the port for WireGuard to the outside.
Also some routers can run WireGuard server on the router. For example Mikrotik routers have WireGuard server built in and ready to configure [0]. Routers running OpenWrt can too [1].
Or you can rent a small VPS and use that as your WireGuard server.
And then, any which where you run the WireGuard server, run the WireGuard client on your laptops, iOS and Android devices, and connect client apps using VPN internal IP addresses. And your NAS etc too, if the WireGuard server isn’t running on the NAS machine itself.
It really is quite quick to set up with server and all clients across devices.
The only real hurdle is that on iOS you have to turn the VPN back on manually after reboot and which is sometimes easily forgotten if you only use your self hosted services occasionally. But you quickly realize oh right I have to open the WireGuard app and turn on the VPN again whenever you try to use one of your self hosted services and the client isn’t connecting.
I think if you want mTLS to have any significance, the application itself has to support it, otherwise you're just doing a VPN again and there's no good reason to use it over Wireguard (especially because an mTLS server will respond to port scans and a Wireguard server will not)
I agree. However, I also want to share photo albums with family and friends with Photo Station and/or Immich. I may also want to run Jellyfin so the same family and friends can watch my collection of... 'Linux ISOs'. Do I simply pinhole those TCP ports through my router and "hope for the best," or is there a better solution?
Run them in containers, put them behind a reverse proxy that does TLS, point fail2ban at the proxy logs. Use strong passwords. Take backups. Life is full of risk, learn to live with it.
Wait out the current wave of madness. In a year or so we will have the most secure software ever seen. We also might start to see servers with Memory Tagging to block exploits not yet found.
I've always wondered: if you take the cause of each CVE, look at underlying cause of that & repeat, how many essential root problems would you be left with?
"Can't do math" (off-by-1 errors etc)
"Sanitize your inputs" (escape sequences, parsing etc)
"What are you referencing?" (null pointers, use-after-free etc)
and error handling. Plain error codes bubbling up a call stack, or bypassing that somehow which may violate program structure.
The oldest one I have still serving data at home is an 1813+ running DSM 7.1.1-42962 Update 9. It's inside my network and just does SMB1 and AFP for my retro computer collection and serves as a dumping ground for security camera footage. Really curious when Syno's going to finally cut this thing off from updates since it's been years since 7.2 came out and it didn't get it.
I just recently took a 415+ off the internet (it had Photo Station and Apache only exposed to the outside). I did the "resistor mod" on its JTAG connector to save its Atom from literally frying itself and it's also still working fine. As usual, the hardware far outlives the software.
I know this is not relevant to the topic at hand but tangentially related:
Does anyone know of any UGREEN UGOS alternatives? I don't mind the terminal but friends prefer a web GUI and for some mundane stuff I too have started to (begrudgingly) prefer it.
Since we’re off topic already - I do have the dxp6800 but I swapped the OS after first boot. Might be worth it to get the hardware but invest in say HexOS or similar
Kind of wild to say there is a critical security vulnerability but the update isn’t out yet. Honestly would have preferred they didn’t tell me until it was patched
I think the answer is mTLS.
Unfortunately, Synology apps don't support it.
Generate the config, one per client, setup the client to only route specific RFC1918 networks and disable on well known wifi networks, and that's it. It literally works for years without any maintenance.
Tailscale is easier (presumably), but also puts a corporate entity between you and your data.
I don't work with computers professionally, at all. It still only took me about 2 hours to get the VPS, get Debian going on it, set up headscale, and connect to it from home. Do I still use corporate Tailscale? Yes, it has some features that aren't beautifully supported on headscale, and so for the moment I'm fine with that. But I do have my backup plan in place if I need it.
mTLS is a better option for distributed systems (service to service mesh networks for attestation of workload identities) instead of for human users.
Do I turn on the VPN when I take a picture and turn it off when finished? Every time?
What if I need multiple VPN's? Living in a country that has a bad geoip reputation, it's already a struggle of switching on and off for individual websites to work.
A basic config to set up a VPN that only adds access to services on the VPN itself is very short and simple, both for WireGuard server and for WireGuard clients.
You can run the WireGuard server from your home computer. For example on your NAS machine itself or some other machine you have at home. And open the port for WireGuard to the outside.
Also some routers can run WireGuard server on the router. For example Mikrotik routers have WireGuard server built in and ready to configure [0]. Routers running OpenWrt can too [1].
Or you can rent a small VPS and use that as your WireGuard server.
And then, any which where you run the WireGuard server, run the WireGuard client on your laptops, iOS and Android devices, and connect client apps using VPN internal IP addresses. And your NAS etc too, if the WireGuard server isn’t running on the NAS machine itself.
It really is quite quick to set up with server and all clients across devices.
The only real hurdle is that on iOS you have to turn the VPN back on manually after reboot and which is sometimes easily forgotten if you only use your self hosted services occasionally. But you quickly realize oh right I have to open the WireGuard app and turn on the VPN again whenever you try to use one of your self hosted services and the client isn’t connecting.
[0]: https://manual.mikrotik.com/docs/virtual-private-networks/wi...
[1]: https://openwrt.org/docs/guide-user/services/vpn/wireguard/b...
Let the family members have their own Linux ISO collections or let them pay streaming scammers.
I am not a big family guy as you can notice. But in my defense no one really cares about my photo albums or ISO files I like.
"Can't do math" (off-by-1 errors etc)
"Sanitize your inputs" (escape sequences, parsing etc)
"What are you referencing?" (null pointers, use-after-free etc)
and error handling. Plain error codes bubbling up a call stack, or bypassing that somehow which may violate program structure.
How many of these fundamental issues are there?
Prepare and parameterize statements you guys.
I just recently took a 415+ off the internet (it had Photo Station and Apache only exposed to the outside). I did the "resistor mod" on its JTAG connector to save its Atom from literally frying itself and it's also still working fine. As usual, the hardware far outlives the software.
Does anyone know of any UGREEN UGOS alternatives? I don't mind the terminal but friends prefer a web GUI and for some mundane stuff I too have started to (begrudgingly) prefer it.